125-22絲網印刷B級導電低CTE環氧粘合劑

說明

125-22是一種可絲網印刷的B級導電單組分環氧粘合劑，適用于

通過絲網印刷和注射器分配。125-22設計用于在粘合過程中顯示小流量。這個產品

在將電路材料與金屬背平面和熱連接時提供優異的導電性和導熱性

下沉。本產品對銅、鋁、陶瓷等多種基材具有優異的附著力。

其他應用包括但不限于組裝電氣和電子部件。這個系統

具有良好的熱穩定性和靈活性的形式。

特色

固化過程中的小流量低CTE

B-可分級屏幕壽命長

優異的耐化學性優異的高溫性能

典型未固化特性

財產價值單位

粘度——布魯克菲爾德帽子粘度計，

25°C時10轉/分20000–30000 cps

比重（水=1）1.88 g/cc

理論覆蓋率@0.001“厚度1~30 in2

屏幕壽命>8小時

填充銀-

1取決于篩網和材料

典型固化性能

財產價值單位

體積電阻率，0.001Ω-cm

熱導率6.5 w/mk

銀含量，固化>60-

熱穩定性高達325攝氏度

有效溫度范圍-55至230攝氏度

玻璃化轉變溫度-TG 150°C

熱膨脹系數-低于TG 50 x 10-6 in/in/℃

-高于TG 60 x 10-6英寸/英寸/攝氏度

拉伸剪切強度，小2000 psi

剝離強度（90°時銅對銅）9 pli

所有技術信息均基于CMI人員獲得的數據，并被認為是可靠的。沒有保證是

關于結果或可能侵犯的明示或暗示的。

修訂日期：11/12/09修訂：A

第2頁，共2頁

固化指南

溫度（攝氏度）時間（分鐘）

160 60個

17530個

200 15個

搬運和儲存

材料在收到后即可使用。存儲凍結以保持*的流屬性。使材料預熱

在打開容器前達到室溫。在使用之前，重新使用任何固定的填料是很重要的。小心

攪拌時不可截留空氣。125-22可以用少量cmi 113-12（快干）或102-03稀釋

（慢干）稀釋劑。

保質期

儲存溫度容器B級薄膜

25°C 2個月1個月

-10°C 6個月3個月

B階段程序

在基材或剝離襯墊上涂上粘合劑。下一步加熱以將固化推進到非粘性階段

冷卻到室溫。要求溫度為100°C至120°C，持續5至15分鐘，B級時間為

與質量有關。鼓勵用戶在給定溫度下試驗干燥時間。

粘合程序

使用時，在一個零件上涂抹B級粘合劑，小心地對齊要粘合的零件，施加均勻的壓力以保持

地點。在200°C下固化15分鐘，或在175°C下固化30分鐘，或在160°C下固化1小時，以獲得更好的粘合效果

薄膜到部分，建議將該部分加熱到40°C。給定的固化時間與質量有關，正時

應在粘合劑和基材達到固化溫度后開始。

健康與安全

在充分通風的情況下使用。遠離火花和明火。避免長時間接觸皮膚和

吸入蒸汽。用肥皂和水清洗皮膚。

125-22絲網印刷B級導電低CTE環氧粘合劑

 125-22
SCREEN-PRINTABLE, B-STAGEABLE, ELECTRICALLY CONDUCTIVE, LOW CTE, EPOXY ADHESIVE
DESCRIPTION
125-22 is a screen-printable, B-Stageable, electrically conductive, one part epoxy adhesive, suitable for application
by screen-printing and syringe dispensing. 125-22 is designed to exhibit minimal flow during bonding. This product
provides superior electrical and thermal conductivity when bonding circuit materials to metal back planes and heat
sinks. This product has excellent adhesion to copper, aluminum and ceramic and a variety of other substrates.
Additional applications include, but are not limited to, assembling electrical and electronic components. This system
features excellent thermal stability and flexibility in the B-Staged form.
UNIQUE FEATURES
? Minimal flow during cure ? Low CTE
? B-Stageable ? Long Screen Life
? Excellent Chemical Resistance ? Excellent High Temperature Performance
TYPICAL UNCURED PROPERTIES
Property Value Units
Viscosity – Brookfield HAT Viscometer,
10 rpm @ 25°C 20,000 – 30,000 cps
Specific Gravity (water = 1) 1.88 g/cc
Theoretical Coverage @ 0.001” Thickness1 ~ 30 in2
Screen Life > 8 hrs
Filler Silver -
1 Dependent on screen mesh and material
TYPICAL CURED PROPERTIES
Property Value Units
Volume Resistivity, max 0.001 Ω - cm
Thermal Conductivity 6.5 W/mK
Percent Silver, cured > 60 -
Thermal Stability Good to 325 º C
Useful Temperature Range -55 to 230 º C
Glass transition Temperature – Tg 150 º C
Coefficient of Thermal Expansion - Below Tg 50 x 10-6 in/in/°C
 - Above Tg 60 x 10-6 in/in/°C
Tensile Shear Strength, min 2000 Psi
Peel Strength (Copper to copper @ 90°) 9 Pli
All technical information is based on data obtained by CMI personnel and is believed to be reliable. No warranty is
either expressed or implied with respect to results or possible infringements on patents.
REVISION DATE: 11/12/09 REVISION: A
Page 2 of 2
CURING GUIDELINES
Temperature (ºC) Time (min.)
 160 60
 175 30
 200 15
HANDLING AND STORAGE
Material is ready to use as received. Store frozen to maintain consistent flow properties. Allow material to warm up
to room temperature before opening container. It is important to resuspend any settled filler before using. Be careful
not entrap air while mixing. 125-22 can be thinned with small amounts of CMI# 113-12 (fast drying), or #102-03
(slow drying) thinners.
 SHELF LIFE
Storage Temperature Containers B-Staged Film
 25°C 2 months 1 month
-10°C 6 months 3 months
B-STAGE PROCEDURE
Apply adhesive to substrate or release liner. Next apply heat to advance the curing to the non-tacky stage when
cooled to room temperature. A temperature of 100°C to 120°C for 5 to 15 minutes is required, B-Stage time is
mass related. User is encouraged to experiment for optimum drying time at a given temperature.
BONDING PROCEDURE
To use, apply b-staged adhesive to one part, carefully align parts to be bonded, apply uniform pressure to maintain
location. Cure for 15 minutes at 200°C, or 30 minutes at 175°C, or 1 hour at 160°C. For better adhesion of the bstaged
film to the first part, it is suggested to warm the part to 40°C. Cure times given are mass related, timing
should start after adhesive and substrates reach curing temperature.
HEALTH AND SAFETY
Use with adequate ventilation. Keep away from sparks and open flames. Avoid prolonged contact with skin and
breathing of vapors. Wash with soap and water to remove from skin.